Finished handmade side-tie bikini bottom sewn from stretchy swimwear fabric

How to Sew a Side-Tie Bikini Bottom With Free Pattern

User avatar placeholder

1 July 2026

In this tutorial, you will learn how to sew a fully lined side-tie bikini bottom using a free pattern in eight sizes.

Making your own swimwear can feel a little intimidating at first. The fabric is stretchy, the pieces are small, and the fit needs to feel secure. Luckily, this side-tie bikini bottom is a very manageable place to begin.

Follow the detailed photo instructions or sew along with the video tutorial. I have also included a free printable pattern in eight sizes.

The finished bikini bottom is fully lined and adjustable on both hips. The side ties make it easier to fine-tune the fit. They also add a playful, handmade detail that looks lovely with many different bikini tops.

About the Free Side-Tie Bikini Bottom Pattern

Fully lined side-tie bikini bottom made with the free sewing pattern

This free side-tie bikini bottom sewing pattern is designed for stretchy swimwear fabrics. Lycra, swim tricot, and four-way stretch fabric are all good choices.

You can sew the bikini bottom with an overlocker or a regular domestic sewing machine. A serger can make the process faster, but it is not essential. I will explain the stitches and settings you can use with an ordinary sewing machine.

Choose your pattern size according to your full hip measurement. Do not rely on your usual ready-to-wear size, as clothing sizes can vary between brands.

Subscribers can download the free pattern in eight sizes at the end of this post.

Part of My Summer Sewing Series

This tutorial is part of my Summer Sewing Series, where we are creating a handmade bikini from start to finish. Earlier in the series, I shared how to draft a bikini top pattern, how to sew a bikini top using my free pattern in eight sizes, and how to draft a bikini bottom pattern.

Watch the Video Tutorial

Prefer to watch the bikini come together? Follow the complete video tutorial below.

The written tutorial contains extra information about sizing, fabric stretch, machine settings and fit. Keep this page open while watching the video so you can check the measurements and sewing tips as you work.

How to Choose Your Bikini Pattern Size

Choose your size according to your full hip circumference.

Measure around the fullest part of your hips and bottom. Keep the tape measure level and parallel to the floor. It should sit close to your body without pulling tightly.

Compare this measurement with the body-measurement chart included with the pattern.

Do not automatically choose your usual shop-bought clothing size. A size M in one brand may be very different from a size M in another.

Why Does the Bikini Pattern Look So Small?

Do not worry if the pattern pieces look smaller than you expected.

Swimwear patterns are drafted with negative ease. This means the finished garment is smaller than the body measurement.

The fabric stretches around your hips when the bikini is worn. This helps it fit closely and stay in place in the water.

Do not size up simply because the paper pattern looks small. First, check that your fabric meets the stretch requirements printed on the pattern.

A fabric with insufficient stretch may make the bikini feel too tight. A fabric with poor recovery may create the opposite problem and become loose after wearing.

Test Your Swimwear Fabric Before Cutting


Testing the stretch and recovery of swimwear fabric before cutting

A successful bikini bottom depends on both stretch and recovery.

Stretch describes how far the fabric can expand. Recovery describes how well it returns to its original shape afterwards.

Stretch a section of your fabric and release it. The material should return close to its original size without staying loose, rippled or wavy.

If the fabric stretches easily but does not bounce back, it may not provide enough support for a fitted bikini bottom.

You should also test the outer fabric and lining together.

Place one layer on top of the other and stretch them at the same time. If the lining is much firmer, it may control the finished fit and make the bikini feel smaller than expected.

Check the stretch guide printed on the pattern before cutting your final fabric.

Recommended Fabrics for Sewing Bikini Bottoms

This side-tie bikini bottom pattern is intended for elastic knit fabrics with strong recovery.

Look for fabric with four-way stretch. This means it stretches both horizontally and vertically.

Recommended materialWhy it worksWhat to check before cutting
Nylon and Lycra swim fabricSmooth, soft and very stretchyMake sure it remains opaque when stretched
Polyester and spandex swim fabricDurable and often resistant to chlorine and fadingConfirm that it is intended for swimwear
Swim tricotLightweight, flexible and comfortableChoose a fabric with strong recovery
Recycled nylon swim fabricSoft and available in many modern printsStretch and thickness vary between brands
Ribbed swimwear fabricAdds texture and a contemporary finishAvoid ordinary fashion rib knit
Matte LycraSupportive and easy to combine with printsTest its recovery before cutting
Swimwear liningAdds coverage and creates a clean inside finishIt should stretch similarly to the main fabric

The best fabric for a bikini bottom is not simply the stretchiest one. It also needs to bounce back.

Avoid cotton jersey, ordinary T-shirt fabric and thin fashion knits. Fabrics containing natural fibres can absorb a large amount of water and may become heavy when wet.

Ordinary rib knit is also unsuitable. Choose ribbed fabric made specifically for swimwear instead.

How Much Fabric Do You Need?

Front view of a handmade adjustable side-tie bikini bottom

A side-tie bikini bottom uses a fairly small amount of fabric. However, the four long ties affect how efficiently the pieces can be arranged.

The following requirements are based on fabric measuring approximately 140–150 cm, or 55–59 inches, wide.

The amounts include the front, back and four side ties. They also allow a small amount for cutting adjustments.

Fabric Requirements for Eight Sizes

SizeMain swim fabricSwimwear lining
XS40 cm / ⅜ yd25 cm / ¼ yd
S40 cm / ⅜ yd25 cm / ¼ yd
M45 cm / ½ yd30 cm / ⅓ yd
L45 cm / ½ yd30 cm / ⅓ yd
XL50 cm / ½ yd35 cm / ⅜ yd
2XL50 cm / ½ yd35 cm / ⅜ yd
3XL55 cm / ⅝ yd40 cm / ⅜ yd
4XL60 cm / ⅔ yd40 cm / ⅜ yd

These amounts should be generous enough for most standard cutting layouts.

You may need slightly more fabric if it is narrow, has a large directional print or needs to be pattern-matched.

The long edge of each tie should follow the direction with the greatest stretch. On many swimwear fabrics, this means arranging the ties across the width of the fabric.

Check the individual cutting layout for your chosen size before buying fabric.

A clever layout can sometimes fit the entire bikini bottom into a surprisingly small remnant. That is excellent news for anyone guarding a drawer of beautiful swimwear scraps as though they were rare jewels.

Supplies

You will need:

  • Four-way stretch swimwear fabric
  • Coordinating swimwear lining
  • Good-quality polyester thread
  • Stretch or ballpoint sewing-machine needle
  • Fabric clips or fine pins
  • Safety pin or loop turner
  • Fabric scissors or rotary cutter
  • Domestic sewing machine or overlocker
  • Optional 6–8 mm swimwear elastic
  • Optional walking foot

Use clips carefully on lightweight Lycra. Too many heavy clips can pull and distort the fabric.

Fine pins can also be used. Keep them inside the seam allowance to reduce the risk of leaving visible holes.

Not sure which sewing tools are worth having? In this post, you can see the sewing, pattern-drafting, and upcycling tools I use regularly and recommend for handmade projects.

Best Needles for Sewing Swimwear

Swimwear fabric needs a needle that can pass between the knitted fibres without cutting them.

A universal needle may work in an emergency. However, a stretch needle is usually a much more reliable choice.

Fabric typeRecommended needle
Lightweight Lycra or swim tricotStretch 75/11
Medium-weight swim fabricStretch 75/11 or 80/12
Thick ribbed swimwear fabricStretch 80/12
Very fine liningStretch or ballpoint 70/10–75/11

If your machine begins skipping stitches, replace the needle before changing every machine setting in sight.

Swimwear fabric can dull or bend a needle more quickly than expected.

Best Thread for Sewing Swimwear

For a domestic sewing machine, use good-quality polyester thread in both the needle and bobbin.

Polyester thread is strong, resilient and suitable for seams that need to stretch.

Avoid cotton thread. It absorbs water and does not have the same resilience as polyester.

Thread typeWhere to use itRecommendation
All-purpose polyester threadDomestic machine needle and bobbinBest general choice
Polyester overlocking threadOverlocker needles and loopersStrong, smooth and flexible
Textured polyester threadOverlocker loopersCreates soft and stretchy seams
Woolly nylonOverlocker loopersSoft and elastic; test for heat sensitivity
Cotton threadNot recommendedAbsorbs water and is less resilient

Textured polyester thread or woolly nylon can create a soft seam with extra give.

Use woolly nylon in the overlocker loopers rather than the needles unless the thread manufacturer says otherwise.

Domestic Sewing-Machine Settings for Swimwear

You do not need an overlocker to sew this side-tie bikini bottom.

A regular home sewing machine can produce strong and flexible seams when you use the correct stitch.

Always test the settings on scraps of your actual outer fabric and lining. Sew through the same number of layers that you will use in the bikini.

Sewing taskRecommended stitchWidthLengthStarting tension
Main stretch seamsNarrow zigzag0.5–1.5 mm2–3 mm3–4
Main stretch seamsLightning or stretch stitchMachine preset2–3 mm3–4
Basting slippery layersLong narrow zigzag0.5–1 mm3–3.5 mmAround 3
Attaching optional elasticMedium zigzag2.5–3.5 mm2.5–3 mm3–4
Closing the turning openingNarrow zigzag0.5–1 mm2.5–3 mm3–4
Optional topstitchingThree-step zigzag4–5 mm1–1.5 mm3–4

These numbers are starting points rather than strict rules.

A tension setting of 4 on one machine may behave very differently from the same setting on another.

The test seam should lie flat without tunnelling, puckering or forming loose loops underneath.

Stretch the seam firmly. If the stitches pop, try a slightly wider zigzag or a shorter stitch length.

A narrow zigzag is often easier to control than an aggressive stretch stitch. Some stretch stitches sew backwards and forwards repeatedly. They create a strong seam but may also stretch delicate Lycra while sewing.

A walking foot can help feed the outer fabric and lining evenly, but it is optional.

Overlocker Settings for Swimwear

A four-thread overlock seam works well for joining the front and back pieces at the crotch.

Begin with the normal settings recommended in your overlocker manual. Adjust them after testing your exact combination of outer fabric and lining.

Overlocker settingSuggested starting point
Seam typeFour-thread overlock
Stitch length2.5–3 mm
Cutting width5–7 mm
Differential feed1.2–1.5
Needle tensionAround 4
Upper-looper tensionAround 4
Lower-looper tensionAround 4
Presser-foot pressureReduce slightly if the fabric stretches

Differential feed helps prevent wavy seams.

Increase it slightly if the sewn edge flares or ripples. Do not assume that more is always better. Too much differential feed can gather the seam and shorten the pattern piece.

After sewing your test seam, allow the fabric to relax for a few minutes. Then inspect it on a flat surface.

Does This Bikini Bottom Need Elastic?

This pattern can be sewn as a fully lined and turned bikini bottom without elastic.

The negative ease and strong recovery of the fabric help it fit closely to the body.

For additional support, you may add narrow swimwear elastic around the leg openings and upper edges before joining the outer fabric to the lining.

Use chlorine-resistant rubber elastic or swimwear elastic measuring approximately 6–8 mm, or ¼ inch, wide.

Do not use ordinary craft elastic if the bikini will be worn in a pool or the sea. It may break down more quickly after exposure to chlorine, salt water, sunscreen and heat.

The four side ties can also be reinforced with narrow swimwear elastic. This is useful when the main fabric is very soft or has only moderate recovery.

Cut the elastic equal to or slightly shorter than the finished tie length. Avoid making it dramatically shorter. Overly tight elastic can make the ties curl or become difficult to turn.

The main tutorial below shows the bikini sewn without elastic. Treat elastic as an optional variation rather than an essential part of the construction.

Pattern Pieces to Cut

The bikini bottom is fully lined. Cut the front and back once from the outer fabric and once from the lining.

Pattern pieceMain fabricLiningTotal
Front bikini pieceCut 1 on the foldCut 1 on the fold2 pieces
Back bikini pieceCut 1 on the foldCut 1 on the fold2 pieces
Side tiesCut 4—4 pieces

You will have eight individual fabric pieces in total:

  • One outer front
  • One outer back
  • One lining front
  • One lining back
  • Four side ties
Cutting the front bikini bottom piece on the fabric fold

The greatest horizontal stretch should travel around the body. It should not run vertically from the waist towards the crotch.

Before cutting all the pieces, fold a small section of fabric and stretch it over your hand. Check that the print does not distort badly and that the fabric remains opaque.

Side-Tie Measurements

Cut four strips measuring:

3 cm × 50 cm

In inches, this is approximately:

1.2 inches × 19.7 inches

The 3 cm measurement is the cutting width, not the finished width.

Once each strip is folded, sewn and turned, the finished tie will be approximately 9 mm, or a little under ⅜ inch, wide. The exact width depends on your seam allowance.

You need four separate ties:

  • Two ties for the front
  • Two ties for the back

Position the greatest direction of stretch along the length of each strip.

For longer bows or trailing ends, increase each strip to 55–60 cm, or approximately 21.7–23.6 inches.

For shorter bows, cut the ties to approximately 45 cm, or 17.7 inches.

It is usually better to begin with ties that are slightly too long. You can shorten them after the first fitting.

Convincing a finished tie to grow another 10 cm requires a level of sewing magic I have not yet achieved.

Four swimwear fabric strips cut for the adjustable side ties

How to Sew a Side-Tie Bikini Bottom

Now that the fabric, machine settings and pattern pieces are ready, we can begin sewing.

The finished bikini contains four adjustable ties.

Three ties are enclosed while the outer fabric and lining are sewn together. The fourth tie is inserted through the turning opening at the end.

That final opening solves two problems at once. It gives us somewhere to turn the bikini right side out and creates a tidy place to attach the last tie.

Step 1: Sew the Four Bikini Ties

Fold one tie strip in half lengthwise with the right sides together.

The folded strip should measure approximately 1.5 cm, or 0.6 inch, wide.

Align the long raw edges and secure them with clips or fine pins.

Folding a Lycra strip in half to sew a bikini tie

Using a narrow zigzag, stretch stitch or overlocker, sew along the long edge with a 6 mm, or ¼ inch, seam allowance.

Sew across one short end and leave the other short end open for turning.

If you are reinforcing the tie with narrow elastic, place it inside the folded strip before sewing. Secure it at the closed end so it cannot slide out while you turn the tie.

Do not pull the fabric as you sew. Allow the feed dogs to move it naturally.

Sewing a narrow bikini side tie with a zigzag stitch

Repeat with the remaining three ties.

Alternative Method for Sewing the Ties

Turning very narrow fabric tubes is not everyone’s favourite activity.

As an alternative, fold both long raw edges towards the centre. Fold the strip in half again and topstitch close to the open edge with a narrow zigzag.

This method creates a flatter tie and removes the need to turn the fabric tube.

Whichever method you choose, use it for all four ties so they have the same width and appearance.

Step 2: Turn the Ties Right Side Out

Attach a small safety pin to the closed end of the first tie.

Push the safety pin inside the fabric tube. Carefully guide it through to the open end.

Pull gently until the entire tie is right side out.

You can also use a loop turner.

Turning a narrow Lycra bikini tie right side out with a safety pin

Roll the seam between your fingers so it sits neatly along one side.

Repeat with the remaining three ties.

Do not worry if the ties look slightly wavy immediately after turning. Lycra often needs a few minutes to relax.

Four finished stretch fabric ties for a side-tie bikini bottom

Step 3: Sew the Outer Bikini at the Crotch

Place the outer front and outer back pieces with their right sides together.

Align the crotch edges.

Pin or clip the seam. Make sure the centre folds and outer crotch corners match.

Sew across the crotch with a narrow zigzag, stretch stitch or four-thread overlock seam.

Outer front and back bikini pieces placed right sides together

Avoid pulling or stretching the crotch seam while sewing.

Step 4: Sew the Lining at the Crotch

Place the front lining and back lining with their right sides together.

Match the crotch edges.

Sew the seam using the same seam allowance used for the outer fabric.

You should now have two complete bikini-bottom shapes:

  • One outer-fabric bikini
  • One lining bikini

Check that the outer and lining crotch seams are the same width.

Neither seam should look stretched or wavy.

Sewing the outer bikini bottom pieces together at the crotch

Step 5: Position the First Three Ties

Lay the outer bikini bottom flat with the right side facing upwards.

Place one finished tie at three of the four outer corners.

The raw end of each tie should align with the raw edge of the bikini. The remaining length should point inwards, towards the centre of the garment.

Pin or baste the ties securely.

Roll or coil the long ends into the middle of the bikini. Keep them well away from the seam line.

This is one of those moments when five extra pins can save fifteen minutes of unpicking.

Leave the fourth corner without a tie. This corner will become the turning opening.

Sewing the swimwear lining pieces together at the crotch

Step 6: Add the Lining

Place the lining over the outer bikini with the right sides together.

The first three ties should now be sandwiched between the outer fabric and lining.

Match all the raw edges carefully.

Pin or clip around:

  • The top front edge
  • The front leg openings
  • The crotch area
  • The back leg openings
  • The top back edge
  • The three corners containing the ties

At the fourth corner, leave an opening large enough to turn the entire bikini right side out.

The opening should be slightly wider than the finished tie. Approximately 3–4 cm, or 1¼–1½ inches, is usually enough.

Outer fabric and lining prepared for sewing the bikini bottom

Step 7: Sew Around the Bikini Bottom

Sew around the entire outer edge with your chosen stretch stitch or overlocker.

Do not sew across the turning opening.

Slow down when sewing over the three enclosed ties.

Check that each tie remains straight and that only its raw end is caught in the seam.

Keep the long sections of the ties safely inside the garment and away from the needle.

When using a domestic sewing machine, secure the stitching carefully at both ends of the opening.

Inspect the entire seam before turning.

Check for skipped stitches, gaps and accidentally trapped sections of tie.

Step 8: Trim and Check the Seam Allowances

Trim bulky corners carefully without cutting through the stitching.

If you used a domestic sewing machine, trim any uneven or bulky seam allowances around the curves.

Do not trim so closely that the seam becomes weak.

Because swimwear fabric does not fray, extensive clipping is not usually necessary. Make only a few tiny clips if a curved area refuses to lie smoothly.

Keep the scissors well away from the stitching line.

An overlocker trims the seam allowances while sewing, so additional trimming is usually unnecessary.

Step 9: Turn the Bikini Right Side Out

Reach through the opening at the fourth corner.

Gently pull the bikini bottom through the gap.

Bring the outer fabric, lining and all three enclosed ties to the right side.

Take your time.

Swimwear fabric is stretchy, but the turning opening does not need to be tested as though it owes you money.

Use your fingers to shape the corners and smooth the curved edges.

Avoid using a sharp tool. It can easily puncture Lycra.

Step 10: Insert the Fourth Tie

At the open corner, fold approximately 1 cm, or ⅜ inch, of the outer fabric and lining seam allowances towards the inside.

Insert the raw end of the fourth tie into the opening.

Push approximately 1–1.5 cm, or ⅜–⅝ inch, of the tie inside the bikini.

Make sure the tie points away from the garment.

Compare it with the tie on the opposite corner. Check that both ties sit at the same angle.

Pin or clip the opening securely.

Positioning three adjustable ties at the corners of the bikini bottom

Step 11: Close the Turning Opening

Close the opening with a narrow zigzag sewn close to the folded edge.

Sew through the outer fabric, inserted tie and lining.

Because this tie will be pulled every time the bikini is tied, sew a second short row of stitching across the inserted end for extra security.

Basting the side ties to the outer bikini fabric

Secure the stitching carefully at both ends.

A straight stitch may be used for a short section of the opening, but a narrow zigzag is a safer choice because it allows a little flexibility.

The fourth tie is now attached and the turning opening is closed.


Side ties rolled inside the bikini before adding the lining

Step 12: Finish and Check the Bikini

Gently roll the edges between your fingers.

Encourage the seams to sit directly on the edge instead of leaning towards the outer fabric or lining.

Optional topstitching can be added around the edges with a three-step zigzag. However, it is not essential.

Free bikini bottom sewing pattern finished in four-way stretch Lycra

Check that:

  • All four ties are firmly attached
  • Two ties are attached to the front
  • Two ties are attached to the back
  • The outer fabric lies smoothly
  • The lining does not pull or twist
  • The crotch seams lie flat
  • The leg openings are symmetrical
  • The turning opening is completely closed
  • No tie has been caught inside an edge seam

Your handmade side-tie bikini bottom is finished.

Handmade side-tie bikini bottom paired with a matching bikini top

How to Adjust the Fit

One of the biggest advantages of a tie-side bikini is that the hip fit can be adjusted with the bows.

However, the ties cannot correct every fitting problem.

The Bikini Feels Too Tight Through the Crotch

Check the front and back rise.

You may need to add length through the body of the pattern rather than simply making the crotch wider.

A larger size may also be needed if both the rise and the overall coverage feel too small.

The Leg Openings Feel Loose

The fabric may have weak recovery.

The pattern may also need slightly more negative ease.

For additional support, add swimwear elastic around the leg openings in your next version.

The Lining Pulls the Outer Fabric

The lining may be firmer or less stretchy than the main fabric.

Choose a softer lining with similar stretch and recovery.

You can also test the next version with slightly less negative ease in the lining.

The Ties Stretch Too Much

Reinforce the ties with narrow swimwear elastic.

Cut the elastic equal to or slightly shorter than the finished tie. Secure it inside the tie before turning.

You can also shorten the ties after fitting if the bows feel too large.

The Back Rides Up

The pattern may need more back coverage, extra back rise or a different leg-opening curve.

Do not automatically make the entire bikini larger.

Adjust the part of the pattern that is causing the problem.

The Bikini Feels Loose When Wet

The fabric may not have enough recovery, or it may absorb too much water.

Test a scrap of fabric in water before making another version. Allow it to become completely wet, then check how much it stretches.

For the next bikini, choose firmer swimwear fabric or add elastic around the openings.

Sewing Swimwear Without an Overlocker

A domestic sewing machine is completely capable of sewing this bikini bottom.

The most important things are:

  • Use a fresh stretch needle
  • Use polyester thread
  • Test the stitch before sewing
  • Avoid pulling the fabric under the presser foot
  • Choose a seam that stretches with the fabric
  • Reduce presser-foot pressure if your machine allows it
  • Baste very slippery layers when necessary
  • Support the fabric so it does not hang from the machine

Do not judge the seam only by how neat it looks.

Stretch it firmly.

A beautiful straight seam that immediately pops is less useful than a slightly visible zigzag that survives an enthusiastic cannonball into the pool.

New to sewing stretchy fabrics? Start with my beginner’s guide to sewing stretch fabric for advice on needles, stitches, machine settings, and avoiding wavy seams. You can also read my guide to nine common knit-sewing mistakes if your machine skips stitches, stretches the fabric, or creates puckered seams.

How to Care for a Handmade Bikini

Rinse your bikini in cool fresh water after swimming.

Hand wash it with a mild detergent. Avoid bleach and fabric softener.

Do not twist or wring the bikini.

Place it on a clean towel and press gently to remove excess water.

Dry it flat and away from direct heat.

Although swimwear is made for sunshine, leaving it to dry in harsh direct sun can fade the fabric and weaken the elastic fibres.

Avoid rough pool edges and textured surfaces. They can snag or pill the fabric.

Do not iron swimwear fabric unless the manufacturer specifically says that it is safe. High heat can damage Lycra and elastic fibres.

Frequently Asked Questions

Can I Sew a Bikini Bottom Without an Overlocker?

Yes.

Use a domestic sewing machine with a stretch needle and polyester thread.

A narrow zigzag is one of the easiest stitches to control. Test it on scraps before sewing the final bikini.

What Stitch Should I Use for Lycra?

Use a narrow zigzag, lightning stitch or another built-in stretch stitch.

The finished seam must stretch without the thread breaking.

A straight stitch is not suitable for the main seams because it cannot expand with the fabric.

Does This Bikini Bottom Need Elastic?

The pattern can be sewn without elastic when made from swimwear fabric with excellent stretch and recovery.

Optional swimwear elastic can be added for firmer support.

Can I Use Two-Way Stretch Fabric?

Four-way stretch fabric is the best choice for this pattern.

Two-way stretch may feel restrictive through the rise and leg openings. It can also change the overall fit.

How Do I Choose My Bikini Pattern Size?

Measure around the fullest part of your hips and bottom.

Choose your size using the body-measurement chart included with the pattern. Do not rely only on your usual shop-bought clothing size.

Why Does My Bikini Lining Feel Too Tight?

The lining may have less stretch than the outer fabric.

Test both fabrics together before cutting. They should stretch and recover at a similar rate.

How Much Fabric Do I Need for a Bikini Bottom?

Depending on the size, you will need approximately 40–60 cm of main swimwear fabric and 25–40 cm of lining.

Extra fabric may be needed for narrow material, directional prints, pattern matching or longer ties.

Can I Make the Side Ties Longer?

Yes.

Increase each strip from 50 cm to approximately 55–60 cm for larger bows or longer trailing ends.

For smaller bows, reduce the ties to approximately 45 cm.

Can I Use the Same Fabric for the Outer Layer and Lining?

You can use the main fabric as lining if it is soft, comfortable and not too thick.

However, using two layers of heavy swimwear fabric may make the bikini feel bulky and reduce its stretch.

A lightweight swimwear lining is usually the safest option.

Save This Side Tie Bikini Bottom Pattern for Later

Not ready to draft your bikini bottom today? Pin this tutorial to your sewing or summer projects board so you can find it easily when you are ready to make your own swimwear.

Your Handmade Side Tie Bikini Bottom Is Ready

And that is how to sew a side-tie bikini bottom using your domestic sewing machine or overlocker.

The adjustable ties make this style surprisingly forgiving. You can loosen or tighten each side until the bikini feels comfortable and secure. Once you understand how the lining and stretchy fabric work together, the construction becomes much less mysterious.

Try on your finished bikini bottom and check the fit before trimming any long tie ends. Make sure the leg openings sit smoothly and the lining stays hidden. Make sure the leg openings sit smoothly and the lining stays hidden. The bikini should feel secure without digging into your skin.

You can pair your new bikini bottom with a matching handmade top or mix it with a different colour or print. It is also a great project for using smaller pieces of leftover swimwear fabric.

Do not worry if your first attempt is not completely perfect. Sewing swimwear gets easier with practice. Each project helps you understand stretch, fabric recovery, and negative ease a little better.

Save the free pattern so you can make another version later. A tiny change in colour, tie length, or fabric print can give the same pattern a completely different look.

Now all that is left to do is tie the sides, check the fit, and enjoy the fact that you made your own swimwear.

Related posts:

how to draft a bikini top pattern

and how to sew a bikini top with a free pattern in eight sizes

how to draft a bikini bottom pattern

Free Side Tie Bikini Bottom Pattern for my Subscribers

Free side-tie bikini bottom sewing pattern in eight sizes

Subscribe to continue reading

Subscribe to get access to the rest of this post and other subscriber-only content.

Image placeholder

I create sewing patterns, refashion projects, and practical tutorials designed to make sewing feel less intimidating and more creative. Most of what you see here starts with something I wanted to wear, remake, or figure out for myself, then I turn the process into a tutorial you can try too.